Batch Config

Network Config

When the mobile phone connects to Wi-Fi, the app can automatically search for devices and channels on the same LAN. You can configure network parameters for them.

Video Config

When the mobile phone connects to Wi-Fi, the app can automatically search for devices and channels on the same LAN. You can configure video parameters for them.

Cloud Upgrade

Upgrade devices in batches remotely.

Go to Batch Config > Cloud Upgrade.
Tap on a project to view devices under it.
Select device(s) and channel(s) and tap Detect to detect new versions.
Select device(s) and channel(s) that can be upgraded and tap Upgrade to upgrade them remotely.

LAN Device Upgrade

Remotely upgrade devices on the same LAN as your phone in batches.

Note

Before you start, please make sure your phone is connected to the Wi-Fi network.

Go to Batch Config > Upgrade LAN Devices. The system will automatically search for and display devices that are on the same LAN as your phone.

Detection + Upgrade

You need to perform upgrade check manually first.

Select the devices you want to upgrade, and then tap Detect.
In the pop-up window, enter the device username and password, and then tap OK. The system will verify the provided username and password and check for available upgrades.
After detection, devices that support upgrade will display Upgradeable on the right side. Select these devices and tap Upgrade. The system will begin the remote upgrade process for the selected devices.

Note

During the upgrade, do not exit the upgrade page or disconnect the device from power; otherwise, the upgrade will fail.

Direct Upgrade

Upgrade check is performed automatically.

Select the devices you want to upgrade, and then tap Upgrade.
In the pop-up window, enter the device username and password, and then tap OK. The system will verify the provided username and password and check for available upgrades.

If an upgrade is available and the provided username and password are correct, the device will upgrade automatically. Otherwise, a failure cause will be displayed (e.g., "The username and password do not match."). To retry the upgrade, select the device in the list, tap Retry, and then enter the correct device username and password.

Note

During the upgrade, do not exit the upgrade page or disconnect the device from power; otherwise, the upgrade will fail.

Batch Config

Network Config

When the mobile phone connects to Wi-Fi, the app can automatically search for devices and channels on the same LAN. You can configure network parameters for them.

Video Config

When the mobile phone connects to Wi-Fi, the app can automatically search for devices and channels on the same LAN. You can configure video parameters for them.

Cloud Upgrade

Upgrade devices in batches remotely.

Go to Batch Config > Cloud Upgrade.
Tap on a project to view devices under it.
Select device(s) and channel(s) and tap Detect to detect new versions.
Select device(s) and channel(s) that can be upgraded and tap Upgrade to upgrade them remotely.

LAN Device Upgrade

Remotely upgrade devices on the same LAN as your phone in batches.

Note

Before you start, please make sure your phone is connected to the Wi-Fi network.

Go to Batch Config > Upgrade LAN Devices. The system will automatically search for and display devices that are on the same LAN as your phone.

Detection + Upgrade

You need to perform upgrade check manually first.

Select the devices you want to upgrade, and then tap Detect.
In the pop-up window, enter the device username and password, and then tap OK. The system will verify the provided username and password and check for available upgrades.
After detection, devices that support upgrade will display Upgradeable on the right side. Select these devices and tap Upgrade. The system will begin the remote upgrade process for the selected devices.

Note

During the upgrade, do not exit the upgrade page or disconnect the device from power; otherwise, the upgrade will fail.

Direct Upgrade

Upgrade check is performed automatically.

Select the devices you want to upgrade, and then tap Upgrade.
In the pop-up window, enter the device username and password, and then tap OK. The system will verify the provided username and password and check for available upgrades.

Note

During the upgrade, do not exit the upgrade page or disconnect the device from power; otherwise, the upgrade will fail.

Network Config

Video Config

Cloud Upgrade

LAN Device Upgrade

Detection + Upgrade

Direct Upgrade

Table of Contents

Batch Config

Network Config

Video Config

Cloud Upgrade

LAN Device Upgrade

Detection + Upgrade

Direct Upgrade

Table of Contents